View MT8816_346281.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ISO-CMOS
(R)
MT8816
8 x 16 Analog Switch Array
Features
* * * * * * * * * * Internal control latches and address decoder Short set-up and hold times Wide operating voltage: 4.5V to 13.2V 12Vpp analog signal capability RON 65 max. @ VDD=12V, 25C RON 10 @ V DD=12V, 25C Full CMOS switch for low distortion Minimum feedthrough and crosstalk Separate analog and digital reference supplies Low power consumption ISO-CMOS technology
ISSUE3
March 1997
Ordering Information MT8816AE MT8816AP 40 Pin Plastic DIP 44 Pin PLCC
-40 to 85C Description
The Mitel MT8816 is fabricated in MITEL's ISOCMOS technology providing low power dissipation and high reliability. The device contains a 8 x 16 array of crosspoint switches along with a 7 to 128 line decoder and latch circuits. Any one of the 128 switches can be addressed by selecting the appropriate seven address bits. The selected switch can be turned on or off by applying a logical one or zero to the DATA input. VSS is the ground refer-ence of the digital inputs. The range of the analog signal is from VDD to VEE. Chip Select (CS) allows the crosspoint array to be cascaded for matrix expansion.
Applications
* * * * * * Key systems PBX systems Mobile radio Test equipment/instrumentation Analog/digital multiplexers Audio/Video switching
CS
STROBE
DATA RESET
VDD
VEE
VSS
AX0 AX1 AX2 AX3 AY0 AY1 AY2
1
1 ****************
7 to 128 Decoder
Latches
8 x 16 Switch Array
128
Xi I/O (i=0-15)
128
*******************
Yi I/O (i=0-7)
Figure 1 - Functional Block Diagram
3-45
MT8816
ISO-CMOS
40 PIN PLASTIC DIP
Figure 2 - Pin Connections
Pin Description
Pin # Name
PDIP PLCC
Description Y3 Analog (Input/Output): this is connected to the Y3 column of the switch array. Y2 Address Line (Input). Master RESET (Input): this is used to turn off all switches regardless of the condition of CS. Active High.
1 2 3 4,5 6,7 8-13 14 15 16 17 18
1 2 3 4,5 7,8 9-14 6,15,16 17 18 19 20
Y3 AY2 RESET
AX3,AX0 X3 and X0 Address Lines (Inputs). X14, X15 X14 and X15 Analog (Inputs/Outputs): these are connected to the X14 and X15 rows of the switch array. X6-X11 NC Y7 VSS Y6 X6-X11 Analog (Inputs/Outputs): these are connected to the X6-X11 rows of the switch array. No Connection Y7 Analog (Input/Output): this is connected to the Y7 column of the switch array. Digital Ground Reference. Y6 Analog (Input/Output): this is connected to the Y6 column of the switch array.
STROBE STROBE (Input): enables function selected by address and data. Address must be stable before STROBE goes high and DATA must be stable on the falling edge of the STROBE. Active High. Y5 VEE Y4 Y5 Analog (Input/Output): this is connected to the Y5 column of the switch array. Negative Power Supply. Y4 Analog (Input/Output): this is connected to the Y4 column of the switch array.
19 20 21 22, 23 24, 25 26, 27
21 22 23 24,25 26,27 30,31
AX1,AX2 X1 and X2 Address Lines (Inputs). AY0,AY1 Y0 and Y1 Address Lines (Inputs). X13, X12 X13 and X12 Analog (Inputs/Outputs): these are connected to the X13 and X12 rows of the switch array.
3-46
VSS Y6 STROBE Y5 VEE Y4 AX1 AX2 AY0 AY1 NC 44 PIN PLCC
Y3 AY2 RESET AX3 AX0 X14 X15 X6 X7 X8 X9 X10 X11 NC Y7 VSS Y6 STROBE Y5 VEE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
VDD Y2 DATA Y1 CS Y0 NC X0 X1 X2 X3 X4 X5 X12 X13 AY1 AY0 AX2 AX1 Y4
X14 X15 X6 X7 X8 X9 X10 X11 NC NC Y7
6 5 4 3 2 1 44 43 42 41 40 7 39 8 38 9 37 10 36 11 35 12 34 13 33 14 32 15 31 16 30 29 17 18 19 20 21 22 23 24 25 26 27 28
NC AX0 AX3 RESET AY2 Y3 VDD Y2 DATA Y1 CS Y0 NC X0 X1 X2 X3 X4 X5 X12 X13 NC
ISO-CMOS
Pin Description (continued)
Pin # Name
PDIP PLCC
MT8816
Description X5-X0 Analog (Inputs/Outputs): these are connected to the X5-X0 rows of the switch array. No Connection. Y0 Analog (Input/Output): this is connected to the Y0 column of the switch array. Chip Select (Input): this is used to select the device. Active High. Y1 Analog (Input/Output): this is connected to the Y1 column of the switch array. DATA (Input): a logic high input will turn on the selected switch and a logic low will turn off the selected switch. Active High. Y2 Analog (Input/Output): this is connected to the Y2 column of the switch array. Positive Power Supply.
28 - 33 34 35 36 37 38 39 40
32-37 28,29, 38 39 40 41 42 43 44
X5-X0 NC Y0 CS Y1 DATA Y2 VDD
Functional Description
The MT8816 is an analog switch matrix with an array size of 8 x 16. The switch array is arranged such that there are 8 columns by 16 rows. The columns are referred to as the Y inputs/outputs and the rows are the X inputs/outputs. The crosspoint analog switch array will interconnect any X I/O with any Y I/O when turned on and provide a high degree of isolation when turned off. The control memory consists of a 128 bit write only RAM in which the bits are selected by the address inputs (AY0-AY2, AX0-AX3). Data is presented to the memory on the DATA input. Data is asynchronously written into memory whenever both the CS (Chip Select) and STROBE inputs are high and are latched on the falling edge of STROBE. A logical "1" written into a memory cell turns the corresponding crosspoint switch on and a logical "0" turns the crosspoint off. Only the crosspoint switches corresponding to the addressed memory location are altered when data is written into memory. The remaining switches retain their previous states. Any combination of X and Y inputs/outputs can be interconnected by establishing appropriate patterns in the control memory. A logical "1" on the RESET input will asynchronously return all memory locations to logical "0" turning off all crosspoint switches regardless of whether CS is high or low. Two voltage reference pins (VSS and VEE) are provided for the MT8816 to enable switching of negative analog signals. The range for digital signals is from VDD to VSS while the range for analog signals is from VDD to VEE. VSS and VEE pins can be tied together if a single voltage reference is needed.
Address Decode
The seven address inputs along with the STROBE and CS (Chip Select) are logically ANDed to form an enable signal for the resettable transparent latches. The DATA input is buffered and is used as the input to all latches. To write to a location, RESET must be low and CS must go high while the address and data are set up. Then the STROBE input is set high and then low causing the data to be latched. The data can be changed while STROBE is high, however, the corresponding switch will turn on and off in accordance with the DATA input. DATA must be stable on the falling edge of STROBE in order for correct data to be written to the latch.
3-47
MT8816
ISO-CMOS
Absolute Maximum Ratings*- Voltages are with respect to VEE unless otherwise stated.
Parameter 1 2 3 4 5 6 Supply Voltage Analog Input Voltage Digital Input Voltage Current on any I/O Pin Storage Temperature Package Power Dissipation PLASTIC DIP Symbol VDD VSS VINA VIN I TS PD -65 Min -0.3 -0.3 -0.3 VSS-0.3 Max 16.0 VDD+0.3 VDD+0.3 VDD+0.3 15 +150 0.6 Units V V V V mA C W
* Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
Recommended Operating Conditions - Voltages are with respect to VEE unless otherwise stated.
Characteristics 1 2 3 4 Operating Temperature Supply Voltage Analog Input Voltage Digital Input Voltage Sym TO VDD VSS VINA VIN Min -40 4.5 VEE VEE VSS Typ 25 Max 85 13.2 VDD-4.5 VDD VDD Units C V V V V Test Conditions
DC Electrical CharacteristicsCharacteristics 1 Quiescent Supply Current
Voltages are with respect to VEE=VSS=0V, VDD =12V unless otherwise stated.
Sym IDD
Min
Typ 1 0.4 5
Max 100 1.5 15 500
0.8+VSS
Units A mA mA nA V V V
Test Conditions All digital inputs at VIN=VSS or VDD All digital inputs at VIN=2.4V + VSS; VSS=7.0V All digital inputs at VIN=3.4V IVXi - VYjI = VDD - VEE See Appendix, Fig. A.1 VSS=7.5V; VEE=0V VSS=6.5V; VEE=0V All digital inputs at VIN = VSS or VDD
2 3 4 5 6
Off-state Leakage Current (See G.9 in Appendix) Input Logic "0" level Input Logic "1" level Input Logic "1" level Input Leakage (digital pins)
IOFF VIL VIH VIH ILEAK
2.0+VSS
1
3.3 0.1 10
A
DC Electrical Characteristics are over recommended temperature range. Typical figures are at 25C and are for design aid only; not guaranteed and not subject to production testing.
DC Electrical Characteristics- Switch Resistance - VDC is the external DC offset applied at the analog I/O pins.
Characteristics Sym 25C Typ 1 On-state VDD=12V Resistance VDD=10V VDD= 5V (See G.1, G.2, G.3 in Appendix) 2 Difference in on-state resistance between two switches (See G.4 in Appendix) RON 45 55 120 Max 65 75 185 70C Typ Max 75 85 215 85C Typ Max 80 90 225 VSS=VEE=0V,VDC=VDD/2, IVXi-VYjI = 0.4V See Appendix, Fig. A.2 Units Test Conditions
RON
5
10
10
10
VDD=12V, VSS=VEE=0, VDC=VDD/2, IVXi-VYjI = 0.4V See Appendix, Fig. A.2
3-48
ISO-CMOS
MT8816
AC Electrical Characteristics - Crosspoint Performance-Voltages are with respect to VDD=5V, VSS=0V,
VEE=-7V, unless otherwise stated.
Characteristics 1 2 3 Switch I/O Capacitance Feedthrough Capacitance Frequency Response Channel "ON" 20LOG(VOUT/VXi)=-3dB Total Harmonic Distortion (See G.5, G.6 in Appendix) Feedthrough Channel "OFF" Feed.=20LOG (VOUT/VXi) (See G.8 in Appendix) Crosstalk between any two channels for switches Xi-Yi and Xj-Yj. Xtalk=20LOG (VYj/VXi). (See G.7 in Appendix).
Sym CS CF F3dB
Min
Typ 20 0.2 45
Max
Units pF pF MHz
Test Conditions f=1 MHz f=1 MHz Switch is "ON"; VINA = 2Vpp sinewave; RL = 1k See Appendix, Fig. A.3 Switch is "ON"; VINA = 2Vpp sinewave f= 1kHz; RL=1k All Switches "OFF"; VINA= 2Vpp sinewave f= 1kHz; RL= 1k. See Appendix, Fig. A.4 VINA=2Vpp sinewave f= 10MHz; RL = 75. VINA=2Vpp sinewave f= 10kHz; RL = 600. VINA=2Vpp sinewave f= 10kHz; RL = 1k. VINA=2Vpp sinewave f= 1kHz; RL = 10k. Refer to Appendix, Fig. A.5 for test circuit. RL=1k; CL=50pF
4 5
THD FDT
0.01 -95
% dB
6
Xtalk
-45 -90 -85 -80
dB dB dB dB
7
Propagation delay through switch
tPS
30
ns
Timing is over recommended temperature range. See Fig. 3 for control and I/O timing details. Typical figures are at 25C and are for design aid only; not guaranteed and not subject to production testing. Crosstalk measurements are for Plastic DIPS only, crosstalk values for PLCC packages are approximately 5dB better. AC Electrical Characteristics - Control and I/O Timings- Voltages are with respect to V =5V, V
DD
SS=0V,
VEE=-7V, unless otherwise stated.
Characteristics 1 Control Input crosstalk to switch (for CS, DATA, STROBE, Address) Digital Input Capacitance Switching Frequency Setup Time DATA to STROBE Hold Time DATA to STROBE Setup Time Address to STROBE Hold Time Address to STROBE Setup Time CS to STROBE Hold Time CS to STROBE STROBE Pulse Width RESET Pulse Width STROBE to Switch Status Delay DATA to Switch Status Delay RESET to Switch Status Delay
Sym CXtalk
Min
Typ 30
Max
Units mVpp
Test Conditions VIN=3V squarewave; RIN=1k, RL=10k. See Appendix, Fig. A.6 f=1MHz RL= 1k, RL= 1k, RL= 1k, RL= 1k, RL= 1k, RL= 1k, RL= 1k, RL= 1k, RL= 1k, RL= 1k, RL= 1k, CL=50pF CL=50pF CL=50pF CL=50pF CL=50pF CL=50pF CL=50pF CL=50pF CL=50pF CL=50pF CL=50pF

2 3 4 5 6 7 8 9 10 11 12 13 14
CDI FO tDS tDH tAS tAH tCSS tCSH tSPW tRPW tS tD tR
10 20 10 10 10 10 10 10 20 40 40 50 35 100 100 100
pF MHz ns ns ns ns ns ns ns ns ns ns ns
Timing is over recommended temperature range. See Fig. 3 for control and I/O timing details. Digital Input rise time (tr) and fall time (tf) = 5ns. Typical figures are at 25C and are for design aid only; not guaranteed and not subject to production testing. Refer to Appendix, Fig. A.7 for test circuit. 3-49
MT8816
ISO-CMOS
tCSS 50% tCSH 50% tRPW 50% 50%
CS
RESET
tSPW 50% tAS 50% 50%
STROBE
ADDRESS
50%
50% tAH
DATA
50% tDS ON tDH
50%
SWITCH* OFF tD tS tR tR
Figure 3 - Control Memory Timing Diagram
* See Appendix, Fig. A.7 for switching waveform
AX0
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
AX1
0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
AX2
0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
AX3
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
AY0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
AY1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
AY2
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Connection*
X0-Y0 X1-Y0 X2-Y0 X3-Y0 X4-Y0 X5-Y0 X12-Y0 X13-Y0 X6-Y0 X7-Y0 X8-Y0 X9-Y0 X10-Y0 X11-Y0 X14-Y0 X15-Y0 X0-Y1 X15-Y1 X0-Y2 X15-Y2 X0-Y3 X15-Y3 X0-Y4 X15-Y4 X0-Y5 X15-Y5 X0-Y6 X15-Y6 X0-Y7 X15-Y7
Table 1. Address Decode Truth Table
* Switch connections are not in ascending order 3-50
Package Outlines
F
A G
D1 D
D2
H E E1 e: (lead coplanarity) A1 I E2 Notes: 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) 4) For D & E add for allowable Mold Protrusion 0.010"
20-Pin
Dim
28-Pin Min
0.165 (4.20) 0.090 (2.29) 0.485 (12.32)
44-Pin Min
0.165 (4.20) 0.090 (2.29) 0.685 (17.40)
68-Pin Min
0.165 (4.20) 0.090 (2.29) 0.985 (25.02)
84-Pin Min
0.165 (4.20) 0.090 (2.29) 1.185 (30.10)
Min
A A1 D/E D1/E1 D2/E2 e F G H I
0.165 (4.20) 0.090 (2.29) 0.385 (9.78) 0.350 (8.890) 0.290 (7.37) 0 0.026 (0.661) 0.013 (0.331)
Max
0.180 (4.57) 0.120 (3.04) 0.395 (10.03)
Max
0.180 (4.57) 0.120 (3.04) 0.495 (12.57)
Max
0.180 (4.57) 0.120 (3.04) 0.695 (17.65)
Max
0.200 (5.08) 0.130 (3.30) 0.995 (25.27)
Max
0.200 (5.08) 0.130 (3.30) 1.195 (30.35)
0.356 0.450 0.456 0.650 0.656 0.950 0.958 1.150 1.158 (9.042) (11.430) (11.582) (16.510) (16.662) (24.130) (24.333) (29.210) (29.413) 0.330 (8.38) 0.004 0.032 (0.812) 0.021 (0.533) 0.390 (9.91) 0 0.026 (0.661) 0.013 (0.331) 0.430 (10.92) 0.004 0.032 (0.812) 0.021 (0.533) 0.590 (14.99) 0 0.026 (0.661) 0.013 (0.331) 0.630 (16.00) 0.004 0.032 (0.812) 0.021 (0.533) 0.890 (22.61) 0 0.026 (0.661) 0.013 (0.331) 0.930 (23.62) 0.004 0.032 (0.812) 0.021 (0.533) 1.090 (27.69) 0 0.026 (0.661) 0.013 (0.331) 1.130 (28.70) 0.004 0.032 (0.812) 0.021 (0.533)
0.050 BSC (1.27 BSC) 0.020 (0.51)
0.050 BSC (1.27 BSC) 0.020 (0.51)
0.050 BSC (1.27 BSC) 0.020 (0.51)
0.050 BSC (1.27 BSC) 0.020 (0.51)
0.050 BSC (1.27 BSC) 0.020 (0.51)
Plastic J-Lead Chip Carrier - P-Suffix
General-10
Package Outlines
3 2 1
E1
E
n-2 n-1 n D A2 L b2 Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) A C eA e b eB eC
Plastic Dual-In-Line Packages (PDIP) - E Suffix
8-Pin DIM Min A A2 b b2 C D D1 E E1 e eA L eB eC
0 0.115 (2.92) 0.014 (0.356) 0.045 (1.14) 0.008 (0.203) 0.355 (9.02) 0.005 (0.13) 0.300 (7.62) 0.240 (6.10) 0.325 (8.26) 0.280 (7.11)
16-Pin Plastic Max Min Max
0.210 (5.33) 0.115 (2.92) 0.014 (0.356) 0.045 (1.14) 0.008 (0.203) 0.780 (19.81) 0.005 (0.13) 0.300 (7.62) 0.240 (6.10) 0.325 (8.26) 0.280 (7.11) 0.195 (4.95) 0.022 (0.558) 0.070 (1.77) 0.014(0.356) 0.800 (20.32)
18-Pin Plastic Min Max
0.210 (5.33) 0.115 (2.92) 0.014 (0.356) 0.045 (1.14) 0.008 (0.203) 0.880 (22.35) 0.005 (0.13) 0.300 (7.62) 0.240 (6.10) 0.325 (8.26) 0.280 (7.11) 0.195 (4.95) 0.022 (0.558) 0.070 (1.77) 0.014 (0.356) 0.920 (23.37)
20-Pin Plastic Min Max
0.210 (5.33) 0.115 (2.92) 0.014 (0.356) 0.045 (1.14) 0.008 (0.203) 0.980 (24.89) 0.005 (0.13) 0.300 (7.62) 0.240 (6.10) 0.325 (8.26) 0.280 (7.11) 0.195 (4.95) 0.022 (0.558) 0.070 (1.77) 0.014 (0.356) 1.060 (26.9)
Plastic
0.210 (5.33) 0.195 (4.95) 0.022 (0.558) 0.070 (1.77) 0.014 (0.356) 0.400 (10.16)
0.100 BSC (2.54) 0.300 BSC (7.62) 0.115 (2.92) 0.150 (3.81) 0.430 (10.92) 0.060 (1.52)
0.100 BSC (2.54) 0.300 BSC (7.62) 0.115 (2.92) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52)
0.100 BSC (2.54) 0.300 BSC (7.62) 0.115 (2.92) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52)
0.100 BSC (2.54) 0.300 BSC (7.62) 0.115 (2.92) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52)
NOTE: Controlling dimensions in parenthesis ( ) are in millimeters.
General-8
Package Outlines
3 2 1
E1
E
n-2 n-1 n D A2 L b2 Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters)
A C eA
e b
eB
Plastic Dual-In-Line Packages (PDIP) - E Suffix
22-Pin DIM Min A A2 b b2 C D D1 E E E1 E1 e eA eA eB L
0.115 (2.93) 0.160 (4.06) 15 0.100 BSC (2.54) 0.400 BSC (10.16) 0.330 (8.39) 0.380 (9.65) 0.125 (3.18) 0.014 (0.356) 0.045 (1.15) 0.008 (0.204) 1.050 (26.67) 0.005 (0.13) 0.390 (9.91) 0.430 (10.92)
24-Pin Plastic Max Min Max
0.250 (6.35) 0.125 (3.18) 0.014 (0.356) 0.030 (0.77) 0.008 (0.204) 1.150 (29.3) 0.005 (0.13) 0.600 (15.24) 0.290 (7.37) 0.485 (12.32) 0.246 (6.25) 0.670 (17.02) .330 (8.38) 0.580 (14.73) 0.254 (6.45) 0.195 (4.95) 0.022 (0.558) 0.070 (1.77) 0.015 (0.381) 1.290 (32.7)
28-Pin Plastic Min Max
0.250 (6.35) 0.125 (3.18) 0.014 (0.356) 0.030 (0.77) 0.008 (0.204) 1.380 (35.1) 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.195 (4.95) 0.022 (0.558) 0.070 (1.77) 0.015 (0.381) 1.565 (39.7)
40-Pin Plastic Min Max
0.250 (6.35) 0.125 (3.18) 0.014 (0.356) 0.030 (0.77) 0.008 (0.204) 1.980 (50.3) 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.195 (4.95) 0.022 (0.558) 0.070 (1.77) 0.015 (0.381) 2.095 (53.2)
Plastic
0.210 (5.33) 0.195 (4.95) 0.022 (0.558) 0.070 (1.77) 0.015 (0.381) 1.120 (28.44)
0.485 (12.32)
0.580 (14.73)
0.485 (12.32)
0.580 (14.73)
0.100 BSC (2.54) 0.600 BSC (15.24) 0.300 BSC (7.62) 0.430 (10.92) 0.115 (2.93) 0.200 (5.08) 15
0.100 BSC (2.54) 0.600 BSC (15.24)
0.100 BSC (2.54) 0.600 BSC (15.24)
0.115 (2.93)
0.200 (5.08) 15
0.115 (2.93)
0.200 (5.08) 15
Shaded areas for 300 Mil Body Width 24 PDIP only
http://www.mitelsemi.com
World Headquarters - Canada Tel: +1 (613) 592 2122 Fax: +1 (613) 592 6909 North America Tel: +1 (770) 486 0194 Fax: +1 (770) 631 8213 Asia/Pacific Tel: +65 333 6193 Fax: +65 333 6192 Europe, Middle East, and Africa (EMEA) Tel: +44 (0) 1793 518528 Fax: +44 (0) 1793 518581
Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively "Mitel") is believed to be reliable. However, Mitel assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or other intellectual property rights owned by Mitel. This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel's conditions of sale which are available on request.
M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation Mitel Semiconductor is an ISO 9001 Registered Company Copyright 1999 MITEL Corporation All Rights Reserved Printed in CANADA TECHNICAL DOCUMENTATION - NOT FOR RESALE

▲Up To Search▲

Price & Availability of MT8816

	To Download MT8816 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .